git-annex-shell(1)           General Commands Manual          git-annex-shell(1)

       git-annex-shell - Restricted login shell for git-annex only SSH access

       git-annex-shell [-c] command [params ...]

       git-annex-shell is a restricted shell, similar to git-shell, which can be
       used as a login shell for SSH accounts.

       Since its syntax is identical to git-shell's, it can be used as a drop-in
       replacement anywhere git-shell is used. For example it can be used as a
       user's restricted login shell.

       Any command not listed below is passed through to git-shell.

       Note that the directory parameter should be an absolute path, otherwise
       it is assumed to be relative to the user's home directory. Also the first
       "/~/" or "/~user/" is expanded to the specified home directory.

       configlist directory
              This outputs a subset of the git configuration, in the same form
              as git config --list. This is used to get the annex.uuid of the
              remote repository.

              When run in a repository that does not yet have an annex.uuid, one
              will be created, as long as a git-annex branch has already been
              pushed to the repository, or if the autoinit= flag is used to
              indicate initialization is desired.

       inannex directory [key ...]
              This checks if all specified keys are present in the annex, and
              exits zero if so.

              Exits 1 if the key is certainly not present in the annex.  Exits
              100 if it's unable to tell (perhaps the key is in the process of
              being removed from the annex).

       lockcontent directory key
              This locks a key's content in place in the annex, preventing it
              from being dropped.

              Once the content is successfully locked, outputs "OK". Then the
              content remains locked until a newline is received from the caller
              or the connection is broken.

              Exits nonzero if the content is not present, or could not be

       dropkey directory [key ...]
              This drops the annexed data for the specified keys.

       recvkey directory key
              This runs rsync in server mode to receive the content of a key,
              and stores the content in the annex.

       sendkey directory key
              This runs rsync in server mode to transfer out the content of a

       transferinfo directory key
              This is typically run at the same time as sendkey is sending a key
              to the remote. Using it is optional, but is used to update
              progress information for the transfer of the key.

              It reads lines from standard input, each giving the number of
              bytes that have been received so far.

       commit directory
              This commits any staged changes to the git-annex branch.  It also
              runs the annex-content hook.

       notifychanges directory
              This is used by git-annex remotedaemon to be notified when refs in
              the remote repository are changed.

       gcryptsetup directory gcryptid
              Sets up a repository as a gcrypt repository.

       p2pstdio directory uuid
              This causes git-annex-shell to communicate using the git-annex p2p
              protocol over stdio. When supported by git-annex-shell, this
              allows multiple actions to be run over a single connection,
              improving speed.

              The uuid is the one belonging to the repository that will be
              communicating with git-annex-shell.

       Most options are the same as in git-annex. The ones specific to git-
       annex-shell are:

              git-annex uses this to specify the UUID of the repository it was
              expecting git-annex-shell to access, as a sanity check.

       -- fields=val fields=val.. --
              Additional fields may be specified this way, to retain
              compatibility with past versions of git-annex-shell (that ignore
              these, but would choke on new dashed options).

              Currently used fields include remoteuuid=, associatedfile=,
              unlocked=, direct=, and autoinit=

       After content is received or dropped from the repository by git-
       annex-shell, it runs a hook, .git/hooks/annex-content (or
       hooks/annex-content on a bare repository). The hook is not currently
       passed any information about what changed.


              If set, disallows any command that could modify the repository.

              Note that this does not prevent passing commands on to git-shell.
              For that, you also need ...

              If set, disallows running git-shell to handle unknown commands.

              If set, git-annex-shell will refuse to run commands that do not
              operate on the specified directory.

       To make a ~/.ssh/authorized_keys file that only allows git-annex-shell to
       be run, and not other commands, pass the original command to the -c

        command="git-annex-shell -c
       ssh-rsa AAAAB3NzaC1y[...]

       To further restrict git-annex-shell to a particular repository, and fully
       lock it down to read-only mode:

       annex-shell -c
       ssh-rsa AAAAB3NzaC1y[...]

       Obviously, ssh-rsa AAAAB3NzaC1y[...] needs to replaced
       with your SSH key. The above also assumes git-annex-shell is available in
       your $PATH, use an absolute path if it is not the case.



       Joey Hess <>