hisaxctrl

HISAXCTRL(8)              Linux System Administration             HISAXCTRL(8)



NAME
       hisaxctrl - configure HiSax-Module

SYNOPSIS
       hisaxctrl DriverId command parameters

DESCRIPTION
       hisaxctrl is used to setup the HiSax-ISDN device driver.  All logging-
       output is sent to the device /dev/isdnctrl. So you can show it by
       executing cat /dev/isdnctrl.
       NOTE: for devfs systems, the program will automatically use
       /dev/isdn/isdnctrl if available.

       The use of hisaxctrl only makes sense if you are using the HiSax
       driver.

OPTIONS
       DriverId
              is used to identify the card when using more than one passive
              card. While loading the hisax module with insmod, or modprobe
              the DriverId is set by appending id=idstring1%idstring2%...  to
              the commandline.

       command
              is an integer selecting the setup category. The following values
              are defined for setting the logging-level of the HiSax-ISDN
              device driver:

               0 reports card status infos.
               1 selects generic debugging.
              11 selects layer 1 development debugging.
              13 selects layer 3 development debugging.

       the following commands are used to enable special features during
       runtime of the HiSax-ISDN device driver.

               2 set B-channel ON delay to parameter (in ms)
               5 set B-channel in leased mode
               6 set B-channel in TESTLOOP mode
               7 set/reset card in Point To Point mode
               8 set card in FIXED TEI mode
               9 load firmware for DSP cards
              10 set B-channel usage limit to 1 or 2 channels
              12 set echo logging mode (only for some cards)
                 B-channel usage limit needs to be 1 if enabled

       parameter
              If the command is 9 then the parameter is the full pathname to
              the file containing the firmware.

              For debug settings this is an integer representing a bitmask.
              Every bit in this mask switches a debug facility on or off.
              Depending on the selected category, the following values are
              defined:

              With generic debugging selected
              (command 1):

              0x001 Link-level <--> hardware-level communication
              0x002 Top state machine
              0x004 D-Channel Q.931 (call control messages)
              0x008 D-Channel Q.921
              0x010 B-Channel X.75
              0x020 D-Channel l2
              0x040 B-Channel l2
              0x080 D-Channel link state debugging
              0x100 B-Channel link state debugging
              0x200 TEI debug
              0x400 LOCK debug in callc.c
              0x800 More debug in callc.c (not for normal use)

              With layer 1 development debugging selected
              (command 11):

              0x001 Warnings (default: on)
              0x002 IRQ status
              0x004 ISAC
              0x008 ISAC FIFO
              0x010 HSCX
              0x020 HSCX FIFO (attention: full B-Channel output!)
              0x040 D-Channel LAPD frame types

              With layer 3 development debugging selected
              (command 13):

              0x001 Warnings (default: on)
              0x002 l3 protocol discriptor errors
              0x004 l3 state machine
              0x008 charge info debugging (1TR6)

EXAMPLE
       hisaxctrl HiSax 1 0x3ff
              enables full generic debugging.

AUTHOR
       © 2000  by Karsten Keil <kkeil@suse.de>

SEE ALSO
       isdnctrl(8), isdn_cause(7), isdninfo(4).



isdn4k-utils-3.1pre4              2001/08/09                      HISAXCTRL(8)