hylafax-log

HYLAFAX-LOG(5F)                                                HYLAFAX-LOG(5F)



NAME
       log/* - session log files

DESCRIPTION
       Files in the log directory in the HylaFAX spooling area contain
       logging/tracing information about transmit and receive sessions.  One
       file exists for each inbound or outbound call, with the filename of the
       form ``cXXXXXXXX'' where XXXXXXXX is a decimal sequence number termed a
       communication identifier.  The amount and kind of tracing information
       that is recorded for a call is defined by the SessionTracing parameter
       specified in the modem configuration file; see hylafax-config(5F).

       Note that logging/tracing information generated by the server outside
       of a session is directed to the syslog(3) service and is controlled by
       the LogFacility and ServerTracing parameters specified in the modem
       configuration file.

       [NB: The remainder of this manual page is out of date.]

SERVER OPERATION
       The following messages may appear when server operation tracing (bit 1)
       is enabled:

       MODEM: Unknown type "%s" ignored.  The ModemType configuration
       parameter was not recognized.

       MODEM %s %s/%s.  This message is generated each time the modem is reset
       and made ready for use.

       %s: Can not lock device..  The UUCP lockfile for the modem could not be
       created because another process has a lockfile already in place.

       %s: Can not open modem (%m).  open(2) on the special device file for
       the modem failed; the error status is presented; c.f.  intro(2).

       %s: Can not open modem (timed out)..  open(2) on the special device
       file blocked and was timed out.  This typically is because the system
       does not support a non-blocking mechanism for opening the device and
       the presented interface requires that carrier be present before the
       open can succeed.

       %s: setuid root failed (%m).  The server process was unable to
       establish root privileges.  This is usually caused by server being
       improperly installed.

       %s: fcntl: %m.  The server was unable to turn off the O_NDELAY bit on
       the open modem file descriptor after doing a non-blocking open of the
       modem device special file.

       schedctl: %m.  (Only on Silicon Graphics systems.)  A schedctl(2)
       system call to set the server process priority failed.

       sched policy=%d, priority=%d.  (Only on POSIX compliant systems.)
       Describes a setscheduler(2) system call to enhance real-time job
       scheduling.

       Unable to set %s scheduling parameters: %m.  (Only on SVR4-style
       systems.)  A priocntl system call to set the server process priority
       failed.

       priocntl(%s): %m.  (Only on SVR4-style systems.)  A priocntl system
       call to get the current process scheduling information failed.

       sched policy=%d, priority=%d.  (Only on POSIX-compliant systems.)
       Indicates a possible change in the system job scheduling due to use of
       PriorityScheduling

       %s: Can not deduce modem type..  The server was unable to reset and
       initialize the modem.  This can be caused by many things: wrong device
       filename, improper cabling, incorrect modem type, incorrect modem
       configuration, etc.

       RECV: Permission denied (unacceptable client TSI).  A receive request
       was denied because the client was denied access through the TSI access
       control list mechanism; c.f.  tsi(5F).

       RECV: Unable to create file "%s" for received data.  The server was
       unable to create a file for writing the received facsimile data.  Check
       the permission on the recvq subdirectory.  Beware also that the server
       uses tempnam(3) to create these files and the presence of the TMPDIR
       environment variable may cause the server to try to create files in a
       directory other than the recvq directory.

       RECV data in "%s".  This is an information message; the received
       facsimile is being placed in the specified filename.

       RECV: empty file "%s" deleted.  A receive operation terminated without
       any good pages being received; consequently the empty file is deleted.

       ACCEPT TSI "%s".  The TSI received during a receive operation was
       accepted and the receive will continue.

       REJECT TSI "%s".  The TSI received during a receive operation was
       rejected and the receive will be aborted at the next opportunity.

       POLL: Unable to create file "%s" for received data.  The server was
       unable to create a file for the polled data.  See also above under
       ``RECV: Unable...''.

       POLL: empty file "%s" deleted.  A poll operation terminated without any
       good pages being received; consequently the empty file is deleted.

       internal muckup, lost polling request.  This message should not appear;
       it indicates the server went to do a poll but did not find the user-
       specified poll request in its job description; c.f.  sendq(5F).

       SEND FAILED: %s.  A transmission failed for the reason shown.

       SEND: Can not open document file "%s", dirnum %d.  The server was
       unable to open the TIFF document file that was to be transmitted.

       SEND: Can not set directory in document file "%s", dirnum %d.  The
       server was unable to access the TIFF directory associated with the next
       page to transmit.  The document file and directory number for the page
       are shown.

       SEND: %s "%s", dirnum %d.  A transmission failed because three attempts
       were made to transmit the same page.  The full reason for the failure
       is displayed along with the document filename and directory number of
       the page that failed.

       SEND: Document is not in a Group 3-compatible format (file %s,
       compression %d).  The TIFF document submitted for transmission was not
       was not compressed with CCITT T.4 compression; the TIFF compression
       code number is shown.  This is treated as a fatal error and the job is
       aborted.

       REJECT: Document was encoded with 2DMR, but client does not support
       this data format.  The document to be transmitted was encoded using the
       optional 2DMR form of the CCITT T.4 standard, but the client
       capabilities indicate this data format is not supported.  This is not a
       fatal error; the server will disconnect and reimage the document using
       1DMH encoding.

       REJECT: Client does not support document page width, max remote page
       width %u, image width %lu.  The document to be transmitted was imaged
       using a page width that is not supported by the client.  This is not a
       fatal error; the server will disconnect and reimage the document using
       the newly discovered client capabilities.

       REJECT: High resolution document is not supported by client, image
       resolution %g line/mm.  The document to be transmitted was imaged using
       7 line/mm, but the client only supports 3.85 line/mm.  This is not a
       fatal error; the server will disconnect and reimage the document using
       the newly discovered client capabilities.

       REJECT: Client does not support document page length, max remote page
       length %d mm, image length %lu rows (%.2f mm).  The document to be
       transmitted was imaged using a page length that is not supported by the
       client.  This is not a fatal error; the server will disconnect and
       reimage the document using the newly discovered client capabilities.

       ABORT: job abort requested.  The server received a request on a command
       FIFO file to abort the current send/receive job.

       ANSWER: Can not lock modem device.  The server went to answer an
       incoming call, but found the device locked for use by another process.
       This is the usual scenario that takes place when an outbound call is
       made through the modem: the echo from data written to the modem causes
       the fax server to wakeup, only to discover the UUCP lockfile for the
       outgoing call.  The fax server will discard its handle on the modem and
       wait for the lockfile to be removed.

       ANSWER: FAX CONNECTION.  The server is initiating service for an
       incoming facsimile call.

       ANSWER: DATA CONNECTION.  The server is initiating service for an
       incoming data call.

       ANSWER: Data connections are not permitted.  The server rejected an
       incoming data call because the configured GettyArgs parameter is null.

       ANSWER: Could not switch modem to data service.  The server was unable
       to initiate service for an incoming data call because of some problem
       in setting up the modem for data use.

       ANSWER: VOICE CONNECTION.  The server is initiating service for an
       incoming voice call.

       ANSWER: Could not switch modem to voice service.  The server was unable
       to initiate service for an incoming voice call because of some problem
       in setting up the modem for voice use.

       ANSWER: %s.  An error was detected by the modem layer while setting up
       an incoming call.

       GETTY: could not create.  The server was unable to create an internal
       data structure used to track a getty process.

       GETTY: can not fork.  The server was unable to fork(2) a new process in
       order to startup the getty program.

       runGetty::setregid: %m.
       runGetty::setreuid: %m.  The server was unable to change the process
       identity before starting up the getty program.

       GETTY: start pid %u, "%s".  The server has started up a getty program
       to service the incoming data call.  The getty process identifier is
       displayed along with the arguments passed to the program.

       GETTY: terminated, exit status %#o.  The server has reaped a getty
       process which it started up.

       Parse error in dial string rules "%s".  The dial string rules in the
       specified file contain a syntax error.  The dialtest(8C) program should
       be used to debug the problem.

       Unknown answer type "%s".  The AnswerRotary configuration parameter has
       an invalid answer type string; consult hylafax-config(5F).

       Syntax error, missing ':' in "%s".
       Syntax error, missing quote mark in "%s".
       Unknown configuration parameter "%s" ignored.  A syntax error was
       encountered in the server configuration file or in a message received
       through the FIFO special file.

FAX PROTOCOL
       The following messages may appear when the facsimile protocol tracing
       (bit 2) is enabled:

       %s: %s (Phase B).  An error occurred during Phase B of Group 3 protocol
       processing.

       Bad HDLC terminating flag received..  During Class 1 ECM; a terminating
       flag for an HDLC frame was corrupt.

       DELAY %u ms.  A %u-millisecond delay was done on the host.

       DIAL %s.  The phone number %s was dialed.  Note that this is the phone
       number passed as an argument to the ModemDialCmd parameter and so may
       not include additional dialing prefixes sent to the modem.

       Error sending T.30 prologue frames.  An error occurred while trying to
       transmit the T.30 DCS frames.

       HDLC frame length invalid.  An ECM HDLC protocol message was
       excessively long.

       HDLC frame not byte-oriented.  Trailing byte: %#x.  An ECM HDLC
       protocol message was received with a number of bits incompatible with
       necessary byte-orientation.

       HDLC frame too short (%u bytes).  An HDLC protocol message was not at
       least 3 bytes long outside of ECM protocol or at least 5 bytes long
       within ECM protocol.

       HDLC frame with bad address field %#x.  An HDLC protocol message was
       sent/received with an address field other than 0xff.

       HDLC frame with bad control field %#x.  An HDLC protocol message was
       sent/received with an invalid control field.

       MODEM ERROR: %s.  While waiting for a modem response/result an error
       was encountered (e.g. an ``ERROR'' result code).

       MODEM protocol botch ("%s"), cannot parse PPR.  The Class 2 modem
       driver encountered an error parsing the post-page response code in a
       ``+FPTS:'' status message.

       MODEM protocol botch, can not parse "%s".  The Class 2 modem driver
       encountered an error parsing the displayed session capabilities string.
       This is usually due to a communication problem between host and modem
       (though it can also be caused by bogus modem firmware).

       MODEM protocol botch: OK without +FPTS:.  The Class 2 modem driver
       encountered an error in the host-modem protocol for receiving
       facsimile.  While waiting for the post-page status (``+FPTS:''), an
       ``OK'' result was received first.  This should never happen.

       MODEM protocol botch: +FET: without +FPTS:.  The Class 2 modem driver
       encountered an error in the host-modem protocol for receiving
       facsimile.  While waiting for the post-page status (``+FPTS:''), a
       ``+FET:'' status message was received first.  This should never happen.

       POLL with CIG "%s".  A poll operation is beginning; the Calling
       Subscriber Identification string that is transmitted to the peer is
       displayed.

       POLL: begin.  The server is beginning a polled receive operation.

       POLL: end.  The server just completed a polled receive operation.

       POLL: %s (begin).  The specified error message occurred when initiating
       the poll operation.

       POLL: %s (end).  The specified error message occurred while terminating
       the poll operation.

       Problem receiving post-page HDLC frame.  An error occurred while
       receiving the HDLC frame that is expected to hold the post-page
       message.

       Problem sending TCF data.  An error occurred while sending the TCF data
       during training.

       RECV PPM: %s.  The specified post-page message was received during a
       receive operation.

       RECV PPR: %s.  The specified post-page response was transmitted during
       a receive operation.

       RECV training at %s %s.  During a receive operation, begin training at
       the specified modulation and signalling rate.

       RECV: begin.  The server is beginning a receive operation.

       RECV: end.  The server just completed a receive operation.

       RECV: %d bytes of data.  During a receive operation the specified
       number of bytes of facsimile data were received for the current page.

       RECV: %lu bytes, %lu total rows.  During a receive operation the
       specified number of bytes of facsimile data were received.  The current
       running total of rows in the current page being received is also
       displayed.

       RECV: %s (begin).  The specified error message occurred when initiating
       the receive operation.

       RECV: %s (end).  The specified error message occurred while terminating
       the receive operation.

       RECV: TCF %u bytes, %u%% non-zero, %u zero-run.  When receiving
       training, the received TCF had the specified number of bytes of which a
       certain percentage was non-zero and the longest consecutive run of zero
       data was found.

       RECV: reject TCF (too many non-zero, max %u%%).  The received TCF was
       deemed unacceptable because there was too high a percentage of non-zero
       data in it.  The Class1TCFMaxNonZero configuration parameter controls
       this decision.

       RECV: reject TCF (zero run too short, min %u).  The received TCF was
       deemed unacceptable because the longest run of zero data was too short.
       The Class1TCFMinZero configuration parameter controls this decision.

       RECV: bad code word 0x%x, len %d, row %lu.

       RECV: begin page.  During a receive operation a new page of data is
       about to received on the high speed message carrier.

       RECV: end page.  During a receive operation, receipt of page of data on
       the high speed message carrier just completed.

       RECV frame FCS check failed.  During ECM protocol, a received HDLC
       frame was received which fails the CRC check and the frame was marked
       as corrupt.

       RECV: premature EOF.  The server did not receive <DLE><ETX> to signal
       the end of a page of facsimile data during a page receive operation.

       REMOTE supports POSTSCRIPT transfer.
       REMOTE does not support POSTSCRIPT transfer.  The peer does or does not
       support the Adobe POSTSCRIPT transfer extensions to the T.30 protocol.

       RECV: Missing EOL after 5 seconds.  The server timed out while
       receiving page data.  This typically is caused by a flow control
       configuration problem that causes data from the modem to the host to be
       stopped.

       RECV: %u bytes of data, %lu total lines.  While receiving page data, %u
       bytes of raw data were received; the current total number of rows in
       the page are also displayed.

       RECV: %lu bad lines %lu consecutive bad lines.  After the completion of
       a page receive, the total number of rows received in error and the
       maximum consecutive rows that were received in error are printed.
       These numbers should always be zero unless copy quality checking is
       done in the host.

       RECV received %u frames of block %u of page %u.  When the server does
       Class 1 ECM; a complete block has been received with a given number of
       frames for a named page.

       RECV received assumed RCP frame with block end.  When the server does
       Class 1 ECM; the block-end indicator was received without a proper RCP
       frame and the receipt of an RCP frame was therefore assumed or feigned.

       RECV received frame number %u.  When the server does Class 1 ECM; the
       numbered image frame has been received.

       RECV received RCP frame.  When the server does Class 1 ECM; the first
       RCP frame was received, which signifies the end of the image block.

       RECV: REJECT page quality, %u%% good lines (%u%% required).  When the
       server does copy quality checking; the received page is deemed to have
       unacceptable quality because the percentage of good rows in the page is
       too low.  This check is controlled by the PercentGoodLines
       configuration parameter.

       RECV: REJECT page quality, %u-line run (max %u).  When the server does
       copy quality checking; the received page is deemed to have unacceptable
       quality because the maximum consecutive rows that were received in
       error exceeds the threshold specified by the MaxBadLines configuration
       parameter.

       RECV sent fourth PPR.  During Class 1 ECM; the server has rejected a
       received image block consecutively four times at which point the sender
       is allowed to either continue to retransmit the block or to end
       retransmissions.

       REMOTE HANGUP: %s (code %s).  The modem returned a hangup status code
       (``+FHNG:'' or ``+FHS:'') to the host.  This indicates a protocol
       problem that was determined within the modem; there is usually nothing
       that the server can do to work around such errors.

       REMOTE TSI "%s".  During a receive operation, the specified TSI was
       received.  This string is checked against the TSI access control list
       described in tsi(5F).

       REMOTE best format %s.  The peers' ``best'' data format according to
       the received DIS frame.  ``Best'' here is based on the belief that
       2DMMR data is better than 2DMR with optional uncompressed data, is
       better than 2DMR data, is better than 1DMH data.

       REMOTE best rate %s.  The peers' best signalling rate according to the
       received DIS frame.

       REMOTE best vres %s.  The peers' best vertical resolution according to
       the received DIS frame.

       REMOTE has document to POLL.  The peer indicates it has a document that
       is available for retrieval.

       REMOTE max %s.  The peers' maximum page width/length according to the
       received DIS frame.

       REMOTE supports error correction.  The peer supports the optional Error
       Correct Mode (ECM) according to the received DIS frame.

       REMOTE wants %s.  The received DCS frame indicates the peer wants the
       specified capability.

       SEND file "%s".  The specified file is about to be transmitted.

       SEND 1D RTC.
       SEND 2D RTC.  A 1D- or 2D-encoded Return To Control (RTC) packet was
       sent to terminate the transmission of a page of facsimile data.

       SEND begin page.  A page of facsimile data is about to be transmitted
       on the high speed message carrier.

       SEND end page.  The transmission of a page of facsimile data on the
       high speed message carrier was completed.

       SEND training at %s %s.  Training is about to be sent to the peer using
       the specified modulation and signalling rate.

       SENT %u bytes of data.  The specified amount of raw facsimile page data
       was transmitted on the high speed message carrier.

       TRAINING failed.
       TRAINING succeeded.  Peer training succeeded or failed.  When sending
       this is based on a message returned by the peer.  When receiving this
       is based on an analysis of the received TCF data.

       USE %s.  Use the specified session capability during a send or receive.
       The capability is based on the peers' best capabilities, the
       capabilities of the modem, and, when transmitting, the characteristics
       of the document.

MODEM OPERATIONS
       The following messages may appear when modem operation tracing (bit 3)
       is enabled:

       MODEM set baud rate: %d baud, input flow %s, output flow %s.  The DTE-
       DCE communication rate was set %d bits/sec on the host and the
       specified flow control method was setup for data received from the
       modem (input) and transmitted to the modem (output).

       MODEM set baud rate: %d baud (flow control unchanged).  The DTE-DCE
       communication rate was changed without modifying the current flow
       control setup.

       MODEM set XON/XOFF/NOW: input %s, output %s.
       MODEM set XON/XOFF/DRAIN: input %s, output %s.
       MODEM set XON/XOFF/FLUSH: input %s, output %s.  The software flow
       control setup for data exchanged between host and modem was changed.
       The NOW , DRAIN , and FLUSH , actions indicate whether the operation is
       done immediately, after any pending data is transmitted to the modem,
       or after pending data is discarded.  On input XON/XOFF characters are
       either ignored (passed through to the server uninterpreted) or
       interpreted (by the system's terminal driver in order to control the
       flow of data).  Likewise, on output XON/XOFF characters are either
       disabled (not generated by the terminal driver), or generated (by the
       terminal driver to effect flow control of data from the modem to the
       host).

       MODEM input buffering enabled.
       MODEM input buffering disabled.  On systems that buffer input data in
       the operating system before delivering it to applications the server
       will enable and disable buffering as best it can in those cases where
       low input latency is critical.

       TIMEOUT: %s.  A timeout occurred while doing a modem-related operation;
       typically reading or writing data.

       Error #%u reading from modem.  An error was returned by a read(2)
       system call.  This usually happens when the modem prematurely drops the
       DCD signal.

MODEM COMMUNICATION
       The following messages may appear when modem communication tracing (bit
       4) is enabled:

       --> [%d:%s].  A %d-byte line of data was received from the modem.
       Printable data are displayed.

       <-- data [%d].  %d bytes of unprintable data were sent to the modem,
       typically facsimile data.

       <-- [%d:%s].  %d bytes of printable data were sent to the modem.  The
       data are displayed.

TIMEOUTS
       The following messages may appear when timeout tracing (bit 5) is
       enabled:
       start %d second timer,
       stop timer (stop the current timeout before it expires), and
       stop timer - timer expired (the current timeout expired.)

HDLC FRAMES
       When tracing of raw HDLC frames (bit 6) is enabled each frame sent and
       received is logged: <-- HDLC<%u:%.*s> for sent frames and -->
       HDLC<%u:%.*s> for received frames.  These messages indicate that a %u-
       byte long HDLC frame was sent or received.  The first byte should
       always be 0xff, the address field specified for dialup communication.
       The second byte should be a frame control field.  The contents of the
       frame is displayed as sequence of bytes in hexadecimal.

BINARY I/O
       When binary input/output (bit 7) is traced there are two types of
       messages logged: <-- <%u:%.*s> for data sent to the modem and -->
       <%u:%.*s> for data received from the modem.  Each message indicates
       that %u bytes of data were transferred.  The data is displayed as a
       sequence of bytes in hexadecimal.

SERVER STATE TRANSITIONS
       Bit 8 controls the tracing of state transitions in the facsimile
       server.  There are currently eight states:
              State        Description
              BASE         during startup and initialization
              RUNNING      normal operation
              MODEMWAIT    waiting for the modem to come ready after a reset
              LOCKWAIT     waiting for a UUCP lockfile to be removed
              GETTYWAIT    waiting for a getty process to terminate
              SENDING      transmitting a facsimile
              ANSWERING    answering an incoming telephone call
              RECEIVING    receiving a facsimile

       STATE CHANGE: %s -> %s (timeout %ld).  The server is changing its
       internal state.  The timeout (in seconds) is used when polling for
       asynchronous events such as a modem becoming ready.

       STATE CHANGE: %s -> %s.  The server is changing its internal state
       without starting a timeout.

QUEUE MANAGEMENT
       Bit 9 controls the tracing the management of the job queue.

       SEND NOT READY: "%s" in %s.  It was not time to send the specified job;
       it will be requeued for the indicated time interval.

       SEND BLOCKED BY CONCURRENT CALL: "%s" in %s.  The specified job is
       blocked by another call to the same phone number; it will be requeued
       for the indicated time interval.

       SEND BLOCKED BY CONCURRENT JOB: "%s" by "%s".  The specified job is
       blocked by another job to the same phone number; it will be requeued
       for the indicated time interval.

       JOB "%s".  The specified job is about to be processed.

       CONVERT POSTSCRIPT: "%s".  The server is about to invoke the POSTSCRIPT
       interpreter to image a document; the shell command used is displayed.

       JOB TIMER START %s.  The timer used to control scanning of the job
       queue is started with the displayed value.

       JOB TIMER STOP (Q head %s tts %s).  The timer used to control scanning
       of the job queue is stopped.  The job at the head of the queue and that
       job's time-to-send are displayed.

       JOB TIMER STOP (Q empty).  The timer used to control scanning of the
       job queue is stopped.  The job queue was found to be empty.

COPY QUALITY
       When doing copy quality checking during a receive operation the
       following messages may be logged if bit 10 is set:

       RECV/CQ: adjusting for trailing noise (%lu run).  The total number of
       rows of data in the received page is adjusted (downward) by %lu.  This
       is done to handle the case where garbage data are received after the
       RTC resulting in some number of consecutive bad rows after the page
       data.

       RECV/CQ: Invalid %s code word, row %lu, x %d.  An invalid 1D- or 2D-
       T.4 code word was encountered on the specified row and horizontal
       offset within the row.  When this occurs the server will scan for an
       EOL code and then regenerate the bad row with the last good row of
       data.

       RECV/CQ: Premature EOL (%s), row %lu, x %d.  An EOL code was
       encountered before a complete row of pixels was received.  When this
       occurs the server will discard the bad row and replace it with the last
       good row that was received.

       RECV/CQ: Bad %s pixel count, row %lu, x %d.  A row of data was received
       with pixel count greater than the negotiated page width.  When this
       occurs the server will discard the bad row and replace it with the last
       good row that was received.

       RECV/CQ: Panic, bad %s decoding state, row %lu, x %d.  The decoder
       state machine was found in a bad internal state.  When this occurs the
       server will scan for an EOL code and regenerate the row using the last
       good received row.

SEE ALSO
       faxq(8C), faxgetty(8C), faxsend(8C), hylafax-config(5F)



                                 May 12, 1996                  HYLAFAX-LOG(5F)