KEEPALIVED(8)               System Manager's Manual              KEEPALIVED(8)

       keepalived - load-balancing and high-availability service

       keepalived [-f|--use-file=FILE] [-P|--vrrp] [-C|--check]
       [-l|--log-console] [-D|--log-detail] [-S|--log-facility={0-7}]
       [-X|--release-vips] [-V|--dont-release-vrrp] [-I|--dont-release-ipvs]
       [-R|--dont-respawn] [-n|--dont-fork] [-d|--dump-conf] [-p|--pid=FILE]
       [-r|--vrrp_pid=FILE] [-c|--checkers_pid=FILE] [-a|--address-monitoring]
       [-x|--snmp] [-A|--snmp-agent-socket=FILE] [-m|--core-dump]
       [-M|--core-dump-format[=PATTERN]] [  |--signum=SIGFUNC] [-v|--version]

       Keepalived provides simple and robust facilities for load-balancing and
       high-availability. The load-balancing framework relies on the
       well-known and widely used Linux Virtual Server (IPVS) kernel module
       providing Layer4 load-balancing. Keepalived implements a set of
       checkers to dynamically and adaptively maintain and manage a
       load-balanced server pool according to their health. Keepalived also
       implements the VRRPv2 and VRRPv3 protocols to achieve high-availability
       with director failover.

        -f, --use-file=FILE
              Use the specified configuration file. The default configuration
              file is "/etc/keepalived/keepalived.conf".

        -P, --vrrp
              Only run the VRRP subsystem. This is useful for configurations
              that do not use the IPVS load balancer.

        -C, --check
              Only run the healthcheck subsystem. This is useful for
              configurations that use the IPVS load balancer with a single
              director with no failover.

        -l, --log-console
              Log messages to the local console. The default behavior is to
              log messages to syslog.

        -D, --log-detail
              Detailed log messages.

        -S, --log-facility=[0-7]
              Set syslog facility to LOG_LOCAL[0-7]. The default syslog
              facility is LOG_DAEMON.

        -X, --release-vips
              Drop VIP on transition from signal.

        -V, --dont-release-vrrp
              Don't remove VRRP VIPs and VROUTEs on daemon stop. The default
              behavior is to remove all VIPs and VROUTEs when keepalived

        -I, --dont-release-ipvs
              Don't remove IPVS topology on daemon stop. The default behavior
              it to remove all entries from the IPVS virtual server table when
              keepalived exits.

        -R, --dont-respawn
              Don't respawn child processes. The default behavior is to
              restart the VRRP and checker processes if either process exits.

        -n, --dont-fork
              Don't fork the daemon process. This option will cause keepalived
              to run in the foreground.

        -d, --dump-conf
              Dump the configuration data.

        -p, --pid=FILE
              Use the specified pidfile for the parent keepalived process. The
              default pidfile for keepalived is "/var/run/",
              unless a network namespace is being used. See NAMESPACES below
              for more details.

        -r, --vrrp_pid=FILE
              Use the specified pidfile for the VRRP child process. The
              default pidfile for the VRRP child process is
              "/var/run/", unless a network namespace is
              being used.

        -c, --checkers_pid=FILE
              Use the specified pidfile for checkers child process. The
              default pidfile for the checker child process is
              "/var/run/" unless a network namespace is
              being used.

        -a, --address-monitoring
              Log all address additions/deletions reported by netlink.

        -x, --snmp
              Enable the SNMP subsystem.

        -A, --snmp-agent-socket=FILE
              Use the specified socket for connection to SNMP master agent.

        -m, --core-dump
              Override the RLIMIT_CORE hard and soft limits to enable
              keepalived to produce a coredump in the event of a segfault or
              other failure.  This is most useful if keepalived has been built
              with 'make debug'.  Core dumps will be created in /, unless
              keepalived is run with the --dont-fork option, in which case
              they will be created in the directory from which keepalived was
              run, or they will be created in the directory of a configuraton
              file if the fault occurs while reading the file.

        -M, --core-dump-pattern[=PATTERN]
              Sets option --core-dump, and also updates
              /proc/sys/kernel/core_pattern to the pattern specified, or
              'core' if none specified.  Provided the parent process doesn't
              terminate abnormally, it will restore
              /proc/sys/kernel/core_pattern to its original value on exit.

              Note: This will also affect any other process producing a core
              dump while keepalived is running.

              Returns the signal number to use for STOP, RELOAD, DATA, STATS
              and JSON.  For example, to stop keepalived running, execute:

              kill -s $(keepalived --signum=STOP) $(cat /var/run/

        -v, --version
              Display the version and exit.

        -h, --help
              Display this help message and exit.

       keepalived can be run in a network namespace (see keepalived.conf(5)
       for configuration details). When run in a network namespace, a local
       mount namespace is also created, and
       /var/run/keepalived/keepalived_NamespaceName is mounted on
       /var/run/keepalived. By default, pid files with the usual default names
       are then created in /var/run/keepalived from the perspective of a
       process in the mount namespace, and they will be visible in
       /var/run/keepalived/keepalived_NamespaceName for a process running in
       the default mount namespace.

       keepalived reacts to a set of signals.  You can send a signal to the
       parent keepalived process using the following:

              kill -SIGNAL $(cat /var/run/

       or better:

              kill -s $(keepalived --signum=SIGFUNC) $(cat /var/run/

       Note that if the first option is used, -SIGNAL must be replaced with
       the actual signal you are trying to send, e.g. with HUP. So it then

              kill -HUP $(cat /var/run/

       Signals other than for STOP, RELOAD, DATA and STATS may change
       depending on the kernel, and also what functionality is included in the
       version of the keepalived depending on the build options used.

              This causes keepalived to close down all interfaces, reload its
              configuration, and start up with the new configuration.

              keepalived will shut down.

              Write configuration data to /tmp/

              Write statistics info to /tmp/keepalived.stats

              Write configuration data is JSON format to /tmp/keepalived.json

       keepalived.conf(5), ipvsadm(8)

       This man page was written by Ryan O'Hara <>

                                  April 2016                     KEEPALIVED(8)