sppp

SPPP(4)                   BSD Kernel Interfaces Manual                   SPPP(4)

NAME
     sppp — point to point protocol network layer for synchronous lines

SYNOPSIS
     device sppp

DESCRIPTION
     The sppp network layer implements the state machine and the Link Control
     Protocol (LCP) of the point to point protocol (PPP) as described in RFC
     1661.  Note that this layer does not provide network interfaces of its own,
     it is rather intended to be layered on top of drivers providing a
     synchronous point-to-point connection that wish to run a PPP stack over it.
     The corresponding network interfaces have to be provided by these hardware
     drivers.

     The sppp layer provides three basic modes of operation.  The default mode,
     with no special flags to be set, is to create the PPP connection
     (administrative Open event to the LCP layer) as soon as the interface is
     taken up with the ifconfig(8) command.  Taking the interface down again
     will terminate the LCP layer and thus all other layers on top.  The link
     will also terminate itself as soon as no Network Control Protocol (NCP) is
     open anymore, indicating that the lower layers are no longer needed.

     Setting the link-level flag link0 with ifconfig(8) will cause the
     respective network interface to go into passive mode.  This means, the
     administrative Open event to the LCP layer will be delayed until after the
     lower layers signals an Up event (rise of “carrier”).  This can be used by
     lower layers to support a dialin connection where the physical layer is not
     available immediately at startup, but only after some external event
     arrives.  Receipt of a Down event from the lower layer will not take the
     interface completely down in this case.

     Finally, setting the flag link1 will cause the interface to operate in
     dial-on-demand mode.  This is also only useful if the lower layer supports
     the notion of a carrier.  Upon configuring the respective interface, it
     will delay the administrative Open event to the LCP layer until either an
     outbound network packet arrives, or until the lower layer signals an Up
     event, indicating an inbound connection.  As with passive mode, receipt of
     a Down event (loss of carrier) will not automatically take the interface
     down, thus it remains available for further connections.

     The sppp layer supports the debug interface flag that can be set with
     ifconfig(8).  If this flag is set, the various control protocol packets
     being exchanged as well as the option negotiation between both ends of the
     link will be logged at level LOG_DEBUG.  This can be helpful to examine
     configuration problems during the first attempts to set up a new
     configuration.  Without this flag being set, only the major phase
     transitions will be logged at level LOG_INFO.

     It is possible to leave the local interface IP address open for negotiation
     by setting it to 0.0.0.0.  This requires that the remote peer can correctly
     supply a value for it based on the identity of the caller, or on the remote
     address supplied by this side.  Due to the way the IPCP option negotiation
     works, this address is being supplied late during the negotiation, which
     might cause the remote peer to make wrong assumptions.

     In a similar spirit the remote address can be set to the magical value
     0.0.0.* which means that we do not care what address the remote side will
     use, as long as it is not 0.0.0.0.  This is useful if your ISP has several
     dial-in servers.  You can of course route add something_or_other 0.0.0.*
     and it will do exactly what you would want it to.

     The PAP and CHAP authentication protocols as described in RFC 1334, and RFC
     1994 resp., are also implemented.  Their parameters are being controlled by
     the spppcontrol(8) utility.

     VJ header compression is implemented, and enabled by default.  It can be
     disabled using spppcontrol(8).

DIAGNOSTICS
     <ifname><ifnum>: <proto> illegal <event> in state <statename>  An event
     happened that should not happen for the current state the respective
     control protocol is in.  See RFC 1661 for a description of the state
     automaton.

     <ifname><ifnum>: loopback  The state automaton detected a line loopback
     (that is, it was talking with itself).  The interface will be temporarily
     disabled.

     <ifname><ifnum>: up  The LCP layer is running again, after a line loopback
     had previously been detected.

     <ifname><ifnum>: down  The keepalive facility detected the line being
     unresponsive.  Keepalive must be explicitly requested by the lower layers
     in order to take place.

SEE ALSO
     inet(4), intro(4), ifconfig(8), spppcontrol(8)

     W. Simpson, Editor, The Point-to-Point Protocol (PPP), RFC 1661.

     G. McGregor, The PPP Internet Protocol Control Protocol (IPCP), RFC 1332.

     B. Lloyd and W. Simpson, PPP Authentication Protocols, RFC 1334.

     W. Simpson, PPP Challenge Handshake Authentication Protocol (CHAP), RFC
     1994.

AUTHORS
     The original implementation of sppp was written in 1994 at Cronyx Ltd.,
     Moscow by Serge Vakulenko <vak@cronyx.ru>.  Jörg Wunsch
     <joerg_wunsch@uriah.heep.sax.de> rewrote a large part in 1997 in order to
     fully implement the state machine as described in RFC 1661, so it could
     also be used for dialup lines.  He also wrote this man page.  Serge later
     on wrote a basic implementation for PAP and CHAP, which served as the base
     for the current implementation, done again by Jörg Wunsch.

BUGS
     Many.

     Currently, only the IPCP control protocol and ip(4) network protocol is
     supported.  More NCPs should be implemented, as well as other control
     protocols for authentication and link quality reporting.

     Negotiation loop avoidance is not fully implemented.  If the negotiation
     does not converge, this can cause an endless loop.

     The various parameters that should be adjustable per RFC 1661 are currently
     hard-coded into the kernel, and should be made accessible through
     spppcontrol(8).

     Passive mode has not been tested extensively.

     Link-level compression protocols should be supported.

BSD                               May 25, 2008                               BSD