UUDECODE(1POSIX)            POSIX Programmer's Manual           UUDECODE(1POSIX)

       This manual page is part of the POSIX Programmer's Manual.  The Linux
       implementation of this interface may differ (consult the corresponding
       Linux manual page for details of Linux behavior), or the interface may
       not be implemented on Linux.

       uudecode — decode a binary file

       uudecode [−o outfile] [file]

       The uudecode utility shall read a file, or standard input if no file is
       specified, that includes data created by the uuencode utility. The
       uudecode utility shall scan the input file, searching for data compatible
       with one of the formats specified in uuencode, and attempt to create or
       overwrite the file described by the data (or overridden by the −o
       option). The pathname shall be contained in the data or specified by the
       −o option. The file access permission bits and contents for the file to
       be produced shall be contained in that data. The mode bits of the created
       file (other than standard output) shall be set from the file access
       permission bits contained in the data; that is, other attributes of the
       mode, including the file mode creation mask (see umask), shall not affect
       the file being produced. If either of the op characters '+' and '−' (see
       chmod) are specified in symbolic mode, the initial mode on which those
       operations are based is unspecified.

       If the pathname of the file to be produced exists, and the user does not
       have write permission on that file, uudecode shall terminate with an
       error. If the pathname of the file to be produced exists, and the user
       has write permission on that file, the existing file shall be

       If the input data was produced by uuencode on a system with a different
       number of bits per byte than on the target system, the results of
       uudecode are unspecified.

       The uudecode utility shall conform to the Base Definitions volume of
       POSIX.1‐2008, Section 12.2, Utility Syntax Guidelines.

       The following option shall be supported by the implementation:

       −o outfile
                 A pathname of a file that shall be used instead of any pathname
                 contained in the input data. Specifying an outfile option-
                 argument of /dev/stdout shall indicate standard output.

       The following operand shall be supported:

       file      The pathname of a file containing the output of uuencode.

       See the INPUT FILES section.

       The input files shall be files containing the output of uuencode.

       The following environment variables shall affect the execution of

       LANG      Provide a default value for the internationalization variables
                 that are unset or null. (See the Base Definitions volume of
                 POSIX.1‐2008, Section 8.2, Internationalization Variables for
                 the precedence of internationalization variables used to
                 determine the values of locale categories.)

       LC_ALL    If set to a non-empty string value, override the values of all
                 the other internationalization variables.

       LC_CTYPE  Determine the locale for the interpretation of sequences of
                 bytes of text data as characters (for example, single-byte as
                 opposed to multi-byte characters in arguments and input files).

                 Determine the locale that should be used to affect the format
                 and contents of diagnostic messages written to standard error.

       NLSPATH   Determine the location of message catalogs for the processing
                 of LC_MESSAGES.


       If the file data header encoded by uuencode is or /dev/stdout, or the
       −o /dev/stdout option overrides the file data, the standard output shall
       be in the same format as the file originally encoded by uuencode.
       Otherwise, the standard output shall not be used.

       The standard error shall be used only for diagnostic messages.

       The output file shall be in the same format as the file originally
       encoded by uuencode.


       The following exit values shall be returned:

        0    Successful completion.

       >0    An error occurred.


       The following sections are informative.

       The user who is invoking uudecode must have write permission on any file
       being created.

       The output of uuencode is essentially an encoded bit stream that is not
       cognizant of byte boundaries. It is possible that a 9-bit byte target
       machine can process input from an 8-bit source, if it is aware of the
       requirement, but the reverse is unlikely to be satisfying. Of course, the
       only data that is meaningful for such a transfer between architectures is
       generally character data.


       Input files are not necessarily text files, as stated by an early
       proposal. Although the uuencode output is a text file, that output could
       have been wrapped within another file or mail message that is not a text

       The −o option is not historical practice, but was added at the request of
       WG15 so that the user could override the target pathname without having
       to edit the input data itself.

       In early drafts, the [−o outfile] option-argument allowed the use of to
       mean standard output. The symbol has only been used previously in
       POSIX.1‐2008 as a standard input indicator.  The standard developers did
       not wish to overload the meaning of in this manner. The /dev/stdout
       concept exists on most modern systems. The /dev/stdout syntax does not
       refer to a new special file. It is just a magic cookie to specify
       standard output.


       chmod, umask, uuencode

       The Base Definitions volume of POSIX.1‐2008, Chapter 8, Environment
       Variables, Section 12.2, Utility Syntax Guidelines

       Portions of this text are reprinted and reproduced in electronic form
       from IEEE Std 1003.1, 2013 Edition, Standard for Information Technology
       -- Portable Operating System Interface (POSIX), The Open Group Base
       Specifications Issue 7, Copyright (C) 2013 by the Institute of Electrical
       and Electronics Engineers, Inc and The Open Group.  (This is POSIX.1-2008
       with the 2013 Technical Corrigendum 1 applied.) In the event of any
       discrepancy between this version and the original IEEE and The Open Group
       Standard, the original IEEE and The Open Group Standard is the referee
       document. The original Standard can be obtained online at
       http://www.unix.org/online.html .

       Any typographical or formatting errors that appear in this page are most
       likely to have been introduced during the conversion of the source files
       to man page format. To report such errors, see
       https://www.kernel.org/doc/man-pages/reporting_bugs.html .

IEEE/The Open Group                   2013                      UUDECODE(1POSIX)